# Wader and Drysuit Repair (2026): Aquaseal, Patches, Neoprene Cement and Cure Times > How to fix leaking waders, drysuits and foul-weather gear with Aquaseal FD, UV and NEO, Tenacious Tape and Seam Grip, with the cure times and steps GEAR AID gives. - Source: https://saltprooflab.com/gear-care/wader-and-drysuit-repair - Publisher: SaltProofLab (https://saltprooflab.com) - Published: 2026-09-30 - Category: gear-care - Tags: wader repair, Aquaseal, drysuit repair, neoprene cement, Tenacious Tape, Seam Grip, wader leak, foul weather gear repair - Method: picks chosen from Amazon listings and brand specs; not hands-on tested; current Amazon prices are on the page; content checked 2026-09-30. - Quick answer: Buy the GEAR AID Aquaseal FD Wader & Boot Repair Kit: a tube of Aquaseal FD, which GEAR AID says cures to a flexible rubber in 8 to 12 hours, plus two Tenacious Tape patches for the outside of a tear. Add Aquaseal NEO for torn neoprene and Aquaseal UV for pinholes you find on the water. ## Key takeaways - Aquaseal FD needs 8 to 12 hours on a flat surface; mixing in Cure Accelerator at 1 part to 3 or 4 parts adhesive cuts that to about two hours, per GEAR AID. - Aquaseal UV cures in about 30 seconds of sunlight but only fills pinholes: GEAR AID says it cannot bond two fabrics and recommends FD for a permanent repair. - Simms warns that repairing your own waders can affect the warranty, so call the maker first if they are still covered. ## Products (chosen from listings, not tested) 1. **GEAR AID Aquaseal FD Wader & Boot Repair Kit** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B0002EERLW) — Buy it to keep in a wader bag for tears and pinholes. - Pros: 0.25 oz Aquaseal FD, two Tenacious Tape hex patches (black and clear), a brush and instructions, per the listing; FD bonds to neoprene, vinyl, nylon and GORE-TEX and cures to flexible rubber, per GEAR AID - Cons: A 0.25 oz tube covers a few small repairs, not a seam job 2. **GEAR AID Aquaseal FD Repair Adhesive and Cure Accelerator, 0.75 oz** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B001BZMGUA) — Buy it if you fix waders the evening before a trip and need them by morning. - Pros: Cure Accelerator cuts FD's cure to about two hours, per GEAR AID; Accelerator doubles as a solvent and surface cleaner, per the listing; Three times the adhesive of the kit tube, enough to seal a seam - Cons: No patches included; mixing adds a step GEAR AID specifies by ratio 3. **GEAR AID Aquaseal UV Repair Adhesive, 0.25 oz** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B001XUI5YY) — Buy it for a quick seal at the truck, then redo the spot with FD at home. - Pros: Cures in about 30 seconds in sunlight, per GEAR AID; Bonds to neoprene, nylon, vinyl and GORE-TEX, per the listing - Cons: Pinhole repairs only; will not cure behind glass or without UV light 4. **GEAR AID Aquaseal NEO Neoprene Contact Cement, 4 fl oz** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B002DZRFIK) — Buy it if a neoprene wader or a wetsuit-style cuff has split along a cut. - Pros: Bonds neoprene and coated materials and cures to black, stretchy rubber, per GEAR AID; Sets in about 30 minutes; the listing names drysuit gaskets, gloves and booties among its uses - Cons: Contact cement: two coats with drying time between, then the edges must meet exactly 5. **GEAR AID Tenacious Tape 3 x 20 in, Black** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B0045CQELI) — Buy it for fast outside patches on foul-weather shells. - Pros: Peel-and-stick tape that bonds to nylon, polyester, vinyl and rubber, per the listing; Cut to size; machine washable after 24 hours, per GEAR AID - Cons: A patch alone does not seal a seam; pair it with an adhesive for a leak 6. **GEAR AID Seam Grip WP Sealant and Adhesive, 1 oz** (details: https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B000OR5PHW) — Buy it when the tape on a rain jacket's seams starts letting water in. - Pros: One 1 oz tube seals up to 12 ft of seams, per the listing; Cures to a flexible rubber seal; applicator brush included - Cons: GEAR AID pitches it for jackets, tents and tarps; for waders it points to Aquaseal FD A pinhole in a pair of waders means a wet leg by the end of a surf session; a split gasket seam on a drysuit means cold water where you least want it. Most of these leaks can be fixed at home with urethane adhesive, neoprene cement or a patch. Which one depends on the fabric and how soon you need the gear back. **How we chose:** we did not test these repairs; the steps and cure times below are GEAR AID's own, and we kept products sold by Amazon.com and in stock on September 30, 2026. ## Six repair products side by side | Product | Use it on | Cure or set time, per GEAR AID | Sold by | Amazon price | |---|---|---|---|---| | [Aquaseal FD Wader & Boot Kit](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B0002EERLW) | Breathable, neoprene and rubber waders | 8–12 hours | Amazon.com | see the current Amazon price on the page | | [Aquaseal FD + Cure Accelerator](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B001BZMGUA) | Same, faster | About 2 hours | Amazon.com | see the current Amazon price on the page | | [Aquaseal UV](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B001XUI5YY) | Pinholes only | About 30 seconds in sun | Amazon.com | see the current Amazon price on the page | | [Aquaseal NEO](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B002DZRFIK) | Neoprene, latex, coated fabric | About 30 minutes | Amazon.com | see the current Amazon price on the page | | [Tenacious Tape](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B0045CQELI) | Nylon and polyester shells | Washable after 24 hours | Amazon.com | see the current Amazon price on the page | | [Seam Grip WP](https://saltprooflab.com/gear-care/wader-and-drysuit-repair#product-B000OR5PHW) | Jacket and bib seams | Not stated on the listing | Amazon.com | see the current Amazon price on the page | ## Before you glue anything: warranty and cleaning Check the warranty first. Simms' [wader care page](https://www.simmsfishing.com/pages/wader-care) warns in capitals that "repairing your own waders can impact your warranty," and gives a phone number to call if in doubt. If your waders are new, a factory repair may cost you nothing. The same page explains why salt gear leaks. Simms says to rinse after saltwater use "as salt can gradually damage the wader seams, fabric, and hardware," and that mildew, not hard use, is the top reason waders come back for repair. Once mildew gets between layers, Simms says, it lifts the seams and causes leaks. ## Finding the leak GEAR AID's [wader repair guide](https://www.gearaid.com/blogs/learn/repair-waders-how-to) starts with the obvious: turn the waders inside out and look over the seams and fabric for gaps. Simms points GORE-TEX wader owners to a video from its repair technician on finding and patching pinholes, on the [same care page](https://www.simmsfishing.com/pages/wader-care). Mark each spot with a pen as you find it. Adhesive goes on a clean, dry surface, so the leak has to be found before the waders are washed and dried for the repair. ## Aquaseal FD: the permanent fix for waders Aquaseal FD is a clear urethane that GEAR AID says bonds to neoprene, nylon, GORE-TEX and vinyl and "cures to a flexible rubber." Its [product page](https://www.gearaid.com/products/aquaseal-repair-adhesive) gives the steps: clean and dry the area, spread a thin layer slightly beyond the damage, lay the item flat and let it cure for 8 to 12 hours. For a tear, GEAR AID's wader guide adds detail. Clean with isopropyl alcohol (max 70%), mask off the area with painter's tape, cover the tear with FD by at least 0.5 in, and cure 8 to 12 hours flat. Its tip for a faster, stronger job: a Tenacious Tape patch outside, FD inside, and a second patch over the adhesive. For a leaking seam, the guide says to apply FD straight onto the seam, 0.25 in onto the fabric each side, and brush it into the stitching and folds. GEAR AID's [Aquaseal tips](https://www.gearaid.com/blogs/learn/aquaseal-tips) say most repairs reach full strength overnight, 10 to 14 hours, longer for thick ones. If you need the waders sooner, the same tips page says to mix in Cure Accelerator at 1 part to 3 or 4 parts Aquaseal FD "for a faster cure of two hours or less." Once the tube is open, GEAR AID's wader guide suggests keeping it in the freezer, which it says extends shelf life to up to six months. ## Aquaseal UV: a pinhole fix at the truck Aquaseal UV cures in sunlight. GEAR AID's [UV tips](https://www.gearaid.com/blogs/learn/aquaseal-uv-tips) say to apply it in full shade, work it into the fabric, overlap the hole by at least 1/4 in, then put the item in the sun, where it cures in about 30 seconds, or 45 for a thick repair, and longer under cloud. The limits are clear in the same notes. Glass blocks the UV it needs, it cannot bond two fabrics, it is "for pinhole repairs only," and it must never go onto waders while someone is wearing them. GEAR AID recommends FD for permanent repairs. ## Aquaseal NEO: neoprene and drysuit seams Neoprene waders and the neoprene parts of drysuits need a contact cement that stretches. GEAR AID's [Aquaseal NEO page](https://www.gearaid.com/products/aquaseal-repair-adhesive-neoprene) gives four steps: clean the tear, coat both edges and wait 5 minutes until tacky, apply a second coat and wait 10 minutes, then press the edges together and hold for 5 to 10 minutes. For drysuits, GEAR AID's Aquaseal tips list sealing gasket seams among FD's uses, and NEO's listing names drysuit gaskets. A torn latex gasket itself is a replacement job; ask the suit's maker before you glue one. ## Foul-weather jackets and bibs Shell fabrics take tape and a seam sealer rather than a thick urethane. Tenacious Tape bonds to nylon, polyester, vinyl and rubber, per its listing, and GEAR AID says a repair becomes machine washable after 24 hours. Seam Grip WP seals up to 12 ft of seams per 1 oz tube and cures to a flexible rubber seal, per its listing. Related: [surf fishing waders](https://saltprooflab.com/foul-weather/surf-fishing-waders) covers wading belts and what to do if waders flood; [rain bibs and jackets](https://saltprooflab.com/foul-weather/fishing-rain-bibs-and-jackets) covers the shells themselves. ## Recalls We found no recall of GEAR AID repair products in the CPSC and FDA marine records our [recall tracker](https://saltprooflab.com/recalls) collects from January 2023. ## Frequently Asked Questions ### Where should waders dry after a salt trip? In a well-ventilated spot out of direct sun, per Simms' [wader care page](https://www.simmsfishing.com/pages/wader-care), which says prolonged UV exposure and daily temperature swings damage the fabric and seams. Turn them inside out once the outside is dry so the lining dries too. ### How should I store waders after a repair? Rolled, not folded, per Simms' [wader care page](https://www.simmsfishing.com/pages/wader-care), which says creases become weak points. Simms also says to store bootfoot waders with the boots resting on the ground to take stress off the boot seam. ### Does Aquaseal FD work on rubber boots? Yes. GEAR AID's [wader guide](https://www.gearaid.com/blogs/learn/repair-waders-how-to) lists rubber among the wader materials FD repairs, and the kit on this page is sold as a wader and boot kit. --- *SaltProofLab is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com.* ## Sources - simmsfishing.com: [Wader care](https://www.simmsfishing.com/pages/wader-care) - gearaid.com: [Repair waders how to](https://www.gearaid.com/blogs/learn/repair-waders-how-to) - gearaid.com: [Aquaseal repair adhesive](https://www.gearaid.com/products/aquaseal-repair-adhesive) - gearaid.com: [Aquaseal tips](https://www.gearaid.com/blogs/learn/aquaseal-tips) - gearaid.com: [UV tips](https://www.gearaid.com/blogs/learn/aquaseal-uv-tips) - gearaid.com: [Aquaseal NEO page](https://www.gearaid.com/products/aquaseal-repair-adhesive-neoprene) --- Last updated: 2026-09-30 Canonical URL: https://saltprooflab.com/gear-care/wader-and-drysuit-repair How to cite: "Wader and Drysuit Repair (2026): Aquaseal, Patches, Neoprene Cement and Cure Times", SaltProofLab, https://saltprooflab.com/gear-care/wader-and-drysuit-repair (checked 2026-09-30). Disclosure: as an Amazon Associate SaltProofLab earns from qualifying purchases. Safety information summarizes public guidance and is not medical advice.